Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
My opener also has 2 wheels on the top of each side of the door: one with a big spool of line and the other just a pulley wheel. So I also lubricated the axles of those spools. You can watch closely while raising/lowering the door to see where the parts spin and move. Now my door runs much quieter, so I must have done something right! Hopefully this will reduce strain on the motor and make it last longer.
Give your garage a great look with garage doors from Menards®. Menards® has all the supplies, tools, and accessories you need to install a stylish new garage door. Choose the perfect door from our selection of residential and commercial garage doors as well as roll-up doors for storage sheds. At Menards®, you will find a wide variety of door sizes ranging from 4 feet to 9 feet wide, 10 feet to 16 feet wide, and over 16 feet wide. Because of the layer of insulation, insulated garage doors are generally quieter than noninsulated doors. Insulated doors also offer improved energy efficiency, so you can stay comfortable while working in the garage no matter what the weather's like outside.
They sell insulation kits at the local big box hardware store and I cringe every time I see them. The box weighs about 15 pounds, which doesn't sound like a lot. It is definitely enough to un-balance a garage door. The springs are calibrated for the weight of the door, and adding weight makes the door "heavy" for the springs. This means that if you pull an operator disconnect handle when the door is in the open position, the door is likely to descend much more quickly than you anticipate. People have been hurt when a garage door came down on them and the momentum knocked them over. Only add weight if the door springs can be re-torqued or replaced with springs of the proper pull.
Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
We also have a wide range of expertise repairing and installing both residential and commercial doors, meaning we can tackle any problem, large or small. We carry a wide range of doors from one of the industry’s leading manufacturers, Clopay, so you can make the choice that makes the most sense for your home and family while feeling confident that you are getting a door of the highest quality.
That sagging garage door is getting harder and harder to open. Garage doors, especially older, wooden models, are as susceptible to the ravages of time and gravity as the rest of us. If your aging doors are a little saggy, square them up with the tension rods positioned on the back of the door. The rods are placed diagonally from top to bottom corners and can be tightened at a turnbuckle to straighten out the door--do a little at time to allow the door to adjust to the change. If your door isn't already equipped with tension rods, you can buy them at home centers.