The Smart Hub: The smart hub includes a Bluetooth receiver for the door sensor, a 2.4 ghz radio to connect to your wireless home network for the system to communicate with Chamberlain’s servers on the internet, and a radio frequency (RF) transmitter to send HomeLink rolling codes to your garage door opener (on a channel in the 300-400mhz range depending on your garage door opener) - just like your remote clicker.
The torsion springs on steel rolling doors work the same way as other torsion springs in the garage door industry. When the door is closed, the spring is wound. The spring is secured to a spring anchor bracket on one end and to the shaft on the other. When the steel rolling door opens, the spring in the barrel supports most of the door weight. The remainder of this weight is lifted by the chain hoist or the operator.

Repair Garage Door Co


Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Your Wireless (Wi-Fi) Network: The Chamberlain documentation says that 2 bars of 2.4ghz WiFi signal is enough for consistent operation. This can be checked by looking on your phone. I say, your mileage may vary. I installed a dedicated access point for the smart hub as I couldn’t get the system to work reliably. A wired connection is also supported.
Do you have a very small amount of space to work with above the top of your garage door? Is your garage ceiling too short to fit your steel garage door normally? This tutorial will explain how to make a low-headroom modification to the brackets for steel garage doors. This will allow a door to operate with a headroom clearance between 9 and 12 inches.

After thousands of cycles opening and closing your garage door, you may start to hear it getting louder and louder. This is relatively easy to notice. What you may not easily see is that after years of operation, and possible maintenance neglect, is the dirt and debris trapped in the roller bearings. This can lead to the rollers turning inefficiently causing bent tracks and rollers. Eventually, if the rollers are in very bad condition, the door may come off the tracks or bust loose from the roller hinges.
When the lay-person typically sees a circuit board, they immediately seize up and think that's it's too advanced for them to fix. In reality, replacing circuit boards for the Chamberlain Liftmaster, Sears, and Craftsman garage door openers is relatively easy with proper instruction. This video will walk you through the process of replacing the circuit board on a Chamberlain Liftmaster, Sears, and Craftsman garage door opener.
In 1921, C.G Johnson invented the upward-acting garage door and revolutionized the way the world entered their homes. For more than 97 years, Overhead Door™ garage doors have been securing and providing families access to their homes. Overhead Door™ garage doors are assembled in the United States and sold at over 450 authorized Ribbon Distributors throughout North America. The Overhead Door™ brand and Overhead Door™ distributors are synonymous with quality and dependability. To ensure you are getting the genuine, the original, make sure to always look for the Red Ribbon.

"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
As a full service garage door company, our trucks are fully stocked to immediately assist you with any of the common garage door or garage door opener problems you may find yourself facing. We carry everything needed and the experience to make accurate repairs for every variety of garage door. Whether you have a steel, wooden, or composite garage door, we will be happy to help you diagnose the problem and apply a solution.
Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340. 

I would like to thank you for the outstanding service I received from your company. Your technician, James, was friendly, courteous, and extremely knowledgable about what needed to be done to return my garage door to a safe operating condition. In addition, the service was completed within 24 hours of my request, at no additional cost. I enthusiastically recommended Precision and will definitely contact you in the future should I require garage door service!
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.
Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.
While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
It’s been more than 30 years since we first started serving the Bakersfield area and all of Kern County, CA, and our approach has remained the same for these three-plus decades: we take care of your garage door needs as quickly and professionally as possible. Here’s a look at what you can expect when you choose King Door for Kern County garage door repair services: Click Here for Best Garage Door Repair Service
×