Location, climate and building codes are just a few factors to consider when determining which type of garage door is right for your home. Depending on the region you live in, you may need to choose a wind load option for your garage door. Wind loaded garage doors help safeguard your home in high wind prone areas. With garage doors serving as the largest and often times the primary entrance to the home, an insulated garage door may also be right for you.
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
With garage door installation costs, these numbers also include the actual purchase of the new door and other hardware, including the tracks, adhesives, connectors and fasteners. Keep in mind that if these numbers seem extreme, garage door replacement and upgrades can yield, on average, one of the highest returns on investments for homeowners — with an expected 85 percent.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
Though you can do some maintenance to your garage doors on your own, it may be a good idea to schedule routine inspections with a professional. A typical service call will include a manual inspection of the door and opener. Then adjustments can be made including spring tension, chain/belt tension, limits and force adjustments and door lubrication. Fees for this service vary from place to place, but garage door repairs typically cost between $147 and $340.
So you've changed the batteries. You've reprogrammed the remote and the mountain that is your garage door still will not be moved. It's quite possible that your opener's motor may need replacing. Cost for replacing these motors runs around $100 and can be purchased at most hardware stores. If you don't have time right now to fix it, but you still need to open that door, there's a red cord that hangs down from the motor which will temporarily disconnect your door from its power, enabling you to open the door manually.
Because it was a Saturday and I knew the garage door company I usually use wasn't open week-ends. I decided to look on the internet for week-end workers. The first site that came up was Precision Overhead Garage. Their website said if you call before noon, you can get an appointment that day. Even though it was 1pm, I decided to call anyway. After explaining that I couldn't close or open my garage door, they told me they would go ahead and schedule a time that day...even though it was after their same-day service cut off time of noon. They told me the technician would arrive between 3pm-5pm and he would call before coming (that was nice because I was able to run errands locally and not have to wait at home for those 2 hours). I also have to mention that although the company used an answering service to take the call and schedule the appointment, the gentleman that helped me was also very professional and courteous. Derrick, the technician that was assigned to the repair, called to tell me he was on his way. It was also within the arrival timeframe the company had promised. When he got to my house, he was polite and professional. He assessed the problem and made sure that I was clear about the cost of the repair and the cost of the service call. I agreed and he immediately went to work. He never tried to sell me any other services or parts or repairs that weren't needed. He was finished within 45 minutes and the door worked perfectly. I was able to pay with a credit card even without them being able to verify the information because it was a week-end. I was very impressed that they did that, especially because I was a new customer and had no history with them. Obviously, by my 5-star rating, I would recommend them to anyone who is looking for a professional garage door company. Thank you to Derrick and Precision Overhead Garage Door Service!!
We offer wide range of stainless metal appliqués. Brushed metal effect or painted any RAL colour. Appliqués will suit most demanding design requirements. If you can’t find what you like an option could be your personal design appliqué. Just send a picture or drawing and we will replicate it on your door. Use our recommended designs or create your own:
Now check the springs. There will be just one on a single-car garage, two on a two-car garage. Roll-up doors are operated by torsion springs, controlled by cables on pulleys. Two-car models can be adjusted by pulling the cable further through the plate above the door, then knotting the end to hold the newly established tension. One-car roll-up door springs should only be adjusted by a professional, as there is such a great amount of tension on the one spring that you could be injured when trying to adjust it yourself. Swing-up door springs are hooked on each side of the door into special notches or holes. To adjust the tension on these springs, simply move the spring hooks to the next notch.
I wish all home repairs were as easy as what happened today. I was sitting in the house working and I hear a loud bang in the garage. I find out that the big spring on our garage door had broken. So, I google some places. I call one, they can’t come for a day or two and gave me a price. I then called Midlothian Garage Doors – Jason asked what size my door is, gave me a price that was better than the first place, gave me a 20% discount because I live in Midlothian, and says he’ll be out within the hour. 45 minutes later, he’s here. 45 minutes later, he’s done. Impressive. I highly recommend Midlothian Garage Doors.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again
Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.
It’s been more than 30 years since we first started serving the Bakersfield area and all of Kern County, CA, and our approach has remained the same for these three-plus decades: we take care of your garage door needs as quickly and professionally as possible. Here’s a look at what you can expect when you choose King Door for Kern County garage door repair services:
Your dream car is parked in out of the elements, but it's not secure because the garage door won't lock. Most garage doors have two horizontal bars that move out from the center of the door into slots along the side of the door in the door track, effectively locking the door in place. Over time, these bars can shift slightly out of position so that they are no longer correctly aligned with the locking slots. To realign the bars, unscrew the guide brackets on the edges of the door so that they are loose enough to move, and then reposition them so that they smoothly guide the locking bars into the locking slots. Lubricate the lock mechanism with machine oil and you're done.