Are the tracks themselves properly aligned? Vertical tracks should be perfectly straight and the same height as one another. Horizontal ones should slant down slightly toward the back of the garage. To set them in proper alignment: loosen - don't remove - bolts and screws for each mounting bracket. Tap the tracks back into proper position. Re-tighten the bolts and screws. Once you've got the tracks aligned properly, take the time to get rid of whatever hardened grease or dirt has built up inside them or on the rollers with a concentrated household cleaner. Be sure to wipe both rollers and tracks dry after cleaning.
Adding a new garage door provides a dramatic difference in your home’s appearance. When neighbors pass by, when guests pull up, or when you return from work, your house will have a distinct beauty that makes it a landmark of the neighborhood. The unique look you’ve always imagined — as well as the material, the finish, and the insulation can be found in our wide selection of garage doors.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Before your garage door decides to break down, it won’t check with your schedule first. Many of our locations offer emergency garage door repair service to help with those unexpected garage door repairs. Check with your local NationServe store for 24-hour appointment availability. Whether you need immediate assistance or an annual maintenance appointment, know that you can depend on our fast and reliable service.

Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.
Does your garage door squeak or make a lot of noise when opening? There are some specific ways to help reduce the squeaking of your garage door. Many people will lubricate everything, but that actually can cause damage and a huge mess. There are some specific things that you can lubricate to help maintain the life of your garage door and reduce noise levels. This video explains how to lubricate your garage door to reduce noise and increase the life of your garage door.

We've seen many garage doors off the track, and in some cases, on the family car. When the garage door system is not functioning optimally, the rollers and tracks can bend, and you may end up with a mess in the garage. If the garage door is salvageable, let us come and safely reinstall the garage door and make sure it won't happen again. Unfortunately, the damage to the family car will have to go through your auto insurance.
Measuring garage door torsion springs is precise, technical work. It often stumps experienced machinists, engineers, and garage door service technicians. In the door business, we often make mistakes ordering springs. The standard joke is that we'll use them as boat anchors, but you may not have a boat! Click to learn how to avoid ordering a boat anchor.
LED & Florescent lights: I hear you asking “why is this important?”. Both can emit radio and electromagnetic interference that can mask the signal between the smart hub and your opener. If you experience unreliable operation - out they go. The last thing I did was remove an LED lamp from a motion sensor fixture nearby and replaced it with a standard incandescent. Since the light is only on for a few minutes I’m not worried about the power usage if it means the garage door will close when commanded.
Schedule garage or overhead door repairs for your home or business and learn more about our same-day services available at our individual locations. Did you know that NationServe is an authorized Wayne Dalton, Genie, and LiftMaster dealer? That’s because we know exactly what it takes to repair and service your garage door. Our skillful installation, repairs, and planned maintenance services will keep your garage door operating at its very best, so you can move forward with your day. 

When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
It’s been more than 30 years since we first started serving the Bakersfield area and all of Kern County, CA, and our approach has remained the same for these three-plus decades: we take care of your garage door needs as quickly and professionally as possible. Here’s a look at what you can expect when you choose King Door for Kern County garage door repair services:
Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, that's exactly the kind of day when moisture and cold can conspire to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is just a minor icy connection between the two that can be broken when you hit the opener button. If the door refuses to budge on the first attempt, though, resist the urge to keep banging on the automatic opener button. This is likely to cause a more serious problem with the garage door opener—including, but not limited to, stripped gears, broken springs, and a burned-out motor on the opener.
Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.
At Kitsap Garage Door, our Clopay commercial garage door catalog is designed to facilitate efficient and long-lasting operations. We have several options appropriate for any commercial industry, from fire stations and restaurants to concessions stands or ticket sales. Explore our selection of commercial garage doors, specialty products and accessories including:
We've seen many garage doors off the track, and in some cases, on the family car. When the garage door system is not functioning optimally, the rollers and tracks can bend, and you may end up with a mess in the garage. If the garage door is salvageable, let us come and safely reinstall the garage door and make sure it won't happen again. Unfortunately, the damage to the family car will have to go through your auto insurance.

Self-storage roll-up doors operate in a similar manner to steel-rolling door springs. Like a steel rolling door, the curtain on these doors wraps around itself as the door opens. The primary difference, however, is that steel rolling doors are made of interlocking slats, while self-storage roll-up doors are just one piece of steel. While steel rolling doors are typically found in heavier commercial and industrial environments, self-storage roll-up doors are common in self-storage facilities.


So you've changed the batteries. You've reprogrammed the remote and the mountain that is your garage door still will not be moved. It's quite possible that your opener's motor may need replacing. Cost for replacing these motors runs around $100 and can be purchased at most hardware stores. If you don't have time right now to fix it, but you still need to open that door, there's a red cord that hangs down from the motor which will temporarily disconnect your door from its power, enabling you to open the door manually. 

I give Chamberlain credit for trying to make the install easy. Considering the different operating environments and variables, it’s a challenge to cover all the bases. Unfortunately, a quick start guide simply isn’t enough in this case and the online instructions are no better. They have made some assumptions about what you need to know (or don't need to know). The above precautions should be spelled out to avoid customer frustration and reduce the number of calls to their help desk (and returned product).
Keith was awesome. Our garage door had a major meltdown, and was completely inoperable. Keith was not only on time, but he was friendly and explained the repair process thoroughly. As the door was stuck partially open, his prompt arrival and repair expertise gave us the peace of mind of having a large access point to our home being resecured. Thank so much!
Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.
Sears can fix almost any broken garage door opener, regardless of the brand or where you bought it. Trying to repair a garage door opener yourself can be dangerous because of the spring tension. The Sears technicians who repair garage door openers are experts; they have the knowledge and experience to repair the garage door opener correctly and safety.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.

Garage Door Opener Company

×