My double garage doors would not open and close properly. We also needed a keypad installed. A snow storm was approaching and we needed the repairs asap. We called Sunday, you came Monday afternoon, replaced spring sets for both doors, installed keypad and we were set. Very professional, got a detailed inspection of both doors and was happy to receive honest appraisal of necessary repairs. Thanks to you we were able to prepare for the storm without worrying how to get the garage doors open to shovel the driveway. Will contact again to completely replace doors. Thanks again.
The Door sensor: This sensor communicates with the smart hub using Bluetooth to indicate door operation and open/ closed condition. During installation it is paired to the smart hub which is best performed with the unit attached to a closed door between 3’ and 10’ from the smart hub. By design, Bluetooth distance is limited to 33’ but don’t count on consistent operation at this extreme end of the range. Consider this distance during installation and future operation.
I'm not a professional, but I watched as my garage doors were serviced last year. The tech used a spray lubricant (I had bought a different brand in the garage door section of a home improvement store). He sprayed the inside of the entire track, top and bottom, the rollers that ride along the track, and all hinges on the door. He sprayed each hinge twice -- once on each side. The techs were more generous with the lubricant than I was when I'd done it before, so don't be afraid to give it a good squirt.
Does your garage door squeak or make a lot of noise when opening? There are some specific ways to help reduce the squeaking of your garage door. Many people will lubricate everything, but that actually can cause damage and a huge mess. There are some specific things that you can lubricate to help maintain the life of your garage door and reduce noise levels. This video explains how to lubricate your garage door to reduce noise and increase the life of your garage door.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."

We offer wide range of stainless metal appliqués. Brushed metal effect or painted any RAL colour. Appliqués will suit most demanding design requirements. If you can’t find what you like an option could be your personal design appliqué. Just send a picture or drawing and we will replicate it on your door. Use our recommended designs or create your own:


Your garage door opener: You obviously have one to which you are adding this system. Do your homework and make sure it’s compatible before you buy. If you’re not positive, call or email them with your make and model numbers in hand. Mine is a Craftsman (Chamberlain) made in 1999 with the door sensors so I was good to go. NOTE: Garage door openers have a limit to the number of remotes they can support. My Craftsman supports 4 remotes. With two HomeLink-connected cars, the remote door opener, and the smart hub I am now at the max allowed by my opener. As a result, I had to decommission my "clickers". Do your homework and factor this into your plans.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
The torsion springs on steel rolling doors work the same way as other torsion springs in the garage door industry. When the door is closed, the spring is wound. The spring is secured to a spring anchor bracket on one end and to the shaft on the other. When the steel rolling door opens, the spring in the barrel supports most of the door weight. The remainder of this weight is lifted by the chain hoist or the operator.

Repair Garage Door Co

×