Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.
Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
The torsion springs on steel rolling doors work the same way as other torsion springs in the garage door industry. When the door is closed, the spring is wound. The spring is secured to a spring anchor bracket on one end and to the shaft on the other. When the steel rolling door opens, the spring in the barrel supports most of the door weight. The remainder of this weight is lifted by the chain hoist or the operator.
Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.

Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.


That sagging garage door is getting harder and harder to open. Garage doors, especially older, wooden models, are as susceptible to the ravages of time and gravity as the rest of us. If your aging doors are a little saggy, square them up with the tension rods positioned on the back of the door. The rods are placed diagonally from top to bottom corners and can be tightened at a turnbuckle to straighten out the door--do a little at time to allow the door to adjust to the change. If your door isn't already equipped with tension rods, you can buy them at home centers.
Do you have a very small amount of space to work with above the top of your garage door? Is your garage ceiling too short to fit your steel garage door normally? This tutorial will explain how to make a low-headroom modification to the brackets for steel garage doors. This will allow a door to operate with a headroom clearance between 9 and 12 inches.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
After working on the car, you find a big oil stain on the driveway. Pulverize a scrap piece of drywall with a hammer (any new home construction site will have dumpsters full of waste pieces of drywall). Crumble the pulverized drywall with your hands and sprinkle on the stain. Leave it overnight, and rinse off in the morning. Reapply and brush in with a bristle broom in cases of stubborn stains.
My opener also has 2 wheels on the top of each side of the door: one with a big spool of line and the other just a pulley wheel. So I also lubricated the axles of those spools. You can watch closely while raising/lowering the door to see where the parts spin and move. Now my door runs much quieter, so I must have done something right! Hopefully this will reduce strain on the motor and make it last longer.
Whether you’re looking for garage door opener maintenance, garage door opener repair, or a brand new garage door opener, Sears Home Services can help. We’re your best, most-trusted option for fast, quick, and easy local service, repair, and maintenance of your automatic garage door opener. Whether your garage door won’t open or close, your garage door opener chain is broken, your automatic garage door opener won’t work after a power outage, your garage door won’t work when it’s cold, or your automatic garage door opener won’t stop running, we’ll connect you to the best local automatic garage door opener repair service technicians in the business. Technicians that are highly trained, licensed, vetted, nearby, and guaranteed to help fix all of your garage door opener needs. We have thousands of local technicians that are always “near me,” that can help you no matter what your appliance emergency.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.

Garage Door Opener Company

×